Worried that gold ring you wear is bent due to constant use? You can fix it easily on your own. Remember, gold is malleable and it can be fixed in a few minutes. Below are a few important tips you should follow to fix up the gold ring that is flattened in due course of time.
Make use of pliers to pull out the section of ring that is crushed and flattened. Keep ring inside the mouth of pliers as much as you can. Move the ring in a circular fashion and then squeeze it properly. Find out if there is any kind of break or even crack in the ring.
Your next step is to file the crack and repair it as much as you can. Press gold band a little bit with the motive to insert the file inside the gap. Do not skip this step even in case of intricate gold ring designs. Remove rough edge and file up broken end quickly. Use mole wrench in order to close the break. Then you should inspect the ring under a magnifying glass and file up broken edge if it is not smooth or tight.
Make sure you clean up your gold ring thoroughly. Check out hallmark inside it in order to find out if it is ten, fourteen or even eighteen carat.
Using high quality tweezers, dip the ring inside borax flux. Heat the gold ring for a short period of time with acetylene torch till flux burns, thereby creating one coating that can protect it from oxidation as well as heat damage.
Cut one millimeter square portion from it with a pair of scissors. In order to avoid problems that may often occur due to melting of ring, you should use solder that is softer than gold used in making the ring. For desirable results, you should use fourteen carat solder. This type of solder melts at lowest temperature.
Heat the ring till the solder melts as well as flows in the joint of the ring. Use acetylene torch for this purpose. It will take only a few seconds. Keep flame low and avoid overheating. Switch off the torch and allow the ring to get cold easily. For other innovative ideas, you can seek the help of the experts of online jewellery store.
File the ring from inside with the help of half-round shaped sleeve. Make the joint smooth. Repeat it to file up the outer portion of the ring. Use sandpaper for final touch-up. You should then slip the ring on mandrel or even dowel. Use acetylene torch to heat heavy ring. The final step is to tap the ring down the mandrel with mallet and make it circular. Rub it till it shines.
 |
| Gold Ring Repairing: Tricky Task! |
Try to rectify the shape of the ring
Make use of pliers to pull out the section of ring that is crushed and flattened. Keep ring inside the mouth of pliers as much as you can. Move the ring in a circular fashion and then squeeze it properly. Find out if there is any kind of break or even crack in the ring.
Your next step is to file the crack and repair it as much as you can. Press gold band a little bit with the motive to insert the file inside the gap. Do not skip this step even in case of intricate gold ring designs. Remove rough edge and file up broken end quickly. Use mole wrench in order to close the break. Then you should inspect the ring under a magnifying glass and file up broken edge if it is not smooth or tight.
Make sure you clean up your gold ring thoroughly. Check out hallmark inside it in order to find out if it is ten, fourteen or even eighteen carat.
Gold Ring Repairing: Get, set and go!
Using high quality tweezers, dip the ring inside borax flux. Heat the gold ring for a short period of time with acetylene torch till flux burns, thereby creating one coating that can protect it from oxidation as well as heat damage.
Cut one millimeter square portion from it with a pair of scissors. In order to avoid problems that may often occur due to melting of ring, you should use solder that is softer than gold used in making the ring. For desirable results, you should use fourteen carat solder. This type of solder melts at lowest temperature.
Heat the ring till the solder melts as well as flows in the joint of the ring. Use acetylene torch for this purpose. It will take only a few seconds. Keep flame low and avoid overheating. Switch off the torch and allow the ring to get cold easily. For other innovative ideas, you can seek the help of the experts of online jewellery store.
Shape it up!
File the ring from inside with the help of half-round shaped sleeve. Make the joint smooth. Repeat it to file up the outer portion of the ring. Use sandpaper for final touch-up. You should then slip the ring on mandrel or even dowel. Use acetylene torch to heat heavy ring. The final step is to tap the ring down the mandrel with mallet and make it circular. Rub it till it shines.
No comments:
Post a Comment